first_imgAfter a couple of weeks of intensive work between the architect (Mikaela Hughes), our passive house consultant and middleman to the suppliers (Malcolm Isaacs), and ourselves, we have the final plans. With the house being factory-built from cross-laminated timber (CLT), there are far fewer changes we can make after this point than to a conventional stick-framed house. But we’re happy with things.The house is small by North American standards, with under 1,600 square feet (or less than 150 square meters) of interior area, and that’s the way we like it. We’ve tried to combine elements of what people around here expect a house to look like, to reflect something of the village feeling, but at the same time, this is not an ordinary house nor does it entirely look like one.However, the differences are subtle — at least from the outside. BLOGS BY DAVID MURAKAMI WOOD Adding the Insulation Building With Cross-Laminated TimberWindows, Doors, and UtilitiesWolfe Island Passive House — An Introduction Passive solar orientationFirst, the orientation and balance are not what people would expect. The windows are predominantly on the south side, regardless of the view, in order to maximize passive solar gain. The southern roof will be completely covered in panels for solar water heating and PV generation. The windows on the east and west bring in light in the morning and evening but also are designed for cross-ventilation in the summer. On the north side, windows are minimal, but this also produces an interesting and slightly whimsical pattern. RELATED ARTICLES Product Guide: Cross-Laminated TimberGeorgia City Bucks Wood High-Rise TrendCan Foam Insulation Be Too Thick?Foam Under Footings The bedrooms face southUpstairs, there is a small landing area, and again the south-north split is evident. On the south side, we have two generously sized bedrooms, and in between a Japanese sitting room with a raised wooden platform covered with tatami (woven grass) mats. This will also double as a guest bedroom, with futons stored beneath the tatami. To the north, there is a walk-in closet, which could be converted into a smaller bedroom if necessary, and on the northeast corner, a Japanese-style bathroom space, with separate water closet, a changing room, and a wet room containing the shower and soaking tub.The chimney from the stove, the solar thermal pipes, and the PV cables will run through the central core of the house from the utility space below up through the storage attic above. The whole house is designed to minimize the distance that water has to travel and the length of pipes from toilets, etc.Outside, the roof extends well out from the wall line, to provide shade for the upper windows from the harshest overhead sun, while maximizing the solar gain at other times. Downstairs, the same effect is created by the porch that runs all along the west and south sides of the house. Editor’s note: David and Kayo Murakami Wood are building what they hope will be Ontario’s first certified Passive House on Wolfe Island, the largest of the Thousand Islands on the St. Lawrence River. They are documenting their work at their blog, Wolfe Island Passive House. For a list of earlier posts in this series, see the sidebar below. Downstairs, an open floor planThe ground floor is dominated by a relatively large space, running the whole length of the house, from the kitchen in the east through the dining room to the lounge in the west. I use the conventional terms because that’s how we’re thinking of the space, although the latter two “rooms” are entirely flexible in how they could be used and laid out.The main entrance is in the northwest corner, and this is where the first element of Japanese thinking comes in. The “genkan” (entrance hall) is a place where you take off outdoor clothes, including shoes — we don’t wear outdoor shoes in the house — and there is a deliberate change of flooring to indicate where this transition occurs. Also in the north half of the ground floor is the utility/machine room, where all the tanks, the energy-recovery ventilator, the control panels, the washing machine, etc. will be. And finally, there’s a dedicated pantry for all the kitchen and food stuff, freeing up the kitchen area itself for actual cooking (which we both enjoy).center_img This solar orientation also affects the interior structure and layout. Places where we will spend most of our time and want to be brightly lit and warmest all are on the south side, whereas the north side of the house has all the utility spaces. R-50 walls and an R-60 roofSo how will this design perform? What about R-values and U-factors?The wall structure should be just over R-50, and the foundation significantly better. The roof structure will be more than R-60. There will be other houses with higher claimed R-values, but the figures here are not claims but are based on tested values for the components, certified by the Passivhaus Institut in Darmstadt, Germany.What’s more, with the precision cutting of the manufacturing — we’re talking 1 mm tolerances — the tightness of the house will be unparalleled, and the windows and doors (about which more in a later post) will be much better performing than any equivalents more commonly available in Canada.There are other considerations when it comes to what kind of R-values we are aiming for. First, we’re by no means in the coldest part of Canada: -25° Celsius (-13°F) is about as cold as it gets here in February — and it is never that cold for more than a few days at a time — compared to -45°C (-49°F) in places like Edmonton.Second, we will have to burn some wood for water heating anyway, which means that the house will never be anything less than comfortably warm in winter. And finally, we already will be exceeding the requirements of the Passive House standard. In short, pushing for much higher performance would mean significantly increased costs and a more bulky look to the house, and all for very limited noticeable gain.We think we’ve got the balance right. The timber walls are over 4 inches thick, not counting insulationThe external walls of the house are 4 1/3 inches (110 mm) thick cross-laminated timber (CLT), wrapped in 11 inches (280 mm) of rigid wood fiberboard insulation, followed by a vapor-permeable moisture barrier and local white cedar siding. The CLT sits on the concrete foundation and the fiberboard forms a continuous layer of insulation with the EPS beneath.The roof also is CLT, but there’s a lot more fiberboard insulation up there: around 14 1/16 inches (360 mm). The roofing will be steel. This will last a long time, and when it does eventually need to be replaced, it can be recycled. Twelve inches of rigid foam under the slabThe most important thing about a Passive House is the envelope: the foundation, walls, and roof. In the sections drawings (see Image #4, below), you can see what we are going for.We’re not deviating much from the standard way most Passive Houses do things with the foundation, which will be an engineered concrete slab with 12 inches (305 mm) of expanded polystyrene (EPS) insulation beneath the slab and about 10 inches (255 mm) of vertical EPS at the edges. The insulation continues out well beyond the foundation itself to provide a frost skirt around the whole foundation. This is the only significant amount of petroleum product we’ll be using in the whole house and one that couldn’t be avoided.last_img

Leave a Reply

Your email address will not be published. Required fields are marked *